AG publications ASAP supplies equipment catalogue

HOW WE CAN HELP YOU PUMP YOUR BILGE....

We offer a wide range of pumps such as submersible, manual and automatic bilge pumps, motor driven impeller pumps, diaphragm pumps and clutched pumps. We also offer spares and accessories including controls, switches, alarms, hose, clips and fittings. ISO 15083 gives the following minimum pump performance requirements at 1 metre head, which offers a useful guide as to which output bilge pump to install.

Boat length

Minimum flow lpm Minimum flow lph

This is just a useful guide, flows shown are a minimum requirement. Any vessel may require more pumping performance or more pumps. It is often prudent to fit multiple pumps possibly at different levels to provide back up when required.

Less than or equal to 6 metres

10 15 30

600 900

Longer than 6 metres but less than 12 metres

Longer than 12 metres

1800

AUTOMATIC BILGE PUMPS

BILGE PUMPS (AUTOMATIC) The eco-friendly Rule Mate series of bilge pumps feature a solid state water sensing technology that eliminates the need for a separate float switch. When water enters the bilge and reaches a certain height, 70mm (2-3/4”), a sensor turns the pump on. After the water is pumped out, another sensor shuts the pump off. The sensors ‘field effect’ technology is eco-friendly because they only sense the dielectric constant of water. In the event of an on board oil spill, straight motor oil that enters the bilge will not turn the pump on. The result is the most technically advanced and eco-friendly bilge pump available in the market place.

PUMPS

• All-in-one pump and switch - no float switch required • Snap-off strainer for easy cleaning • Anti-fouling impeller • Available in 500, 750, 1,100, 1,500 and 2,000 GPH • Limited 3 year warranty For control panels, please see page 229.

504159

Part no.

Model

Volts

Max amp draw

Maximum output lph (US gph)

Outlet mm (inch)

Dimensions mm (l x w x h) 152 x 83 x 114 152 x 83 x 114 152 x 83 x 114 152 x 83 x 114 152 x 83 x 114 152 x 83 x 114 150 x 110 x 150 150 x 110 x 150 150 x 110 x 150

504158* 504159 504178* 504179* 504188* 504189* 504108 504118 504119

RM500A

12V 2.5A 24V 1.3A 12V 4A 24V 2A 24V 2A 12V 7A 12V 12A 24V 6A 12V 5A

1,892 (500) 1,892 (500) 2,839 (750) 2,839 (750) 4,164 (1,100) 4,164 (1,100) 5,678 (1500) 7,571 (2,000) 7,571 (2,000)

19 (3/4”) 19 (3/4”) 19 (3/4”) 19 (3/4”)

RM500-24

RM750A

RM750A-24

RM1100A

28 (1-1/8”) 28 (1-1/8”) 28 (1-1/8”) 28 (1-1/8”) 28 (1-1/8”)

RM1100A-24

RM1500 RM2000

504108

RM2000-24

* Supplied with 90° and straight adaptor.

BILGE PUMPS (AUTOMATIC COMPUTERISED OPERATION) The Rule automatic submersible bilge pumps eliminate the need for a separate float switch to activate the pump. Once power is supplied to the bilge pump, starting and stopping is completely automatic. These pumps turn on and check for water every 2-1/2 minutes, during this check the pump runs for approximately 1 second and checks for resistance or drag against the impeller. If resistance is encountered, it will run until water is no longer present. Thereafter the automatic bilge pump resumes the 2-1/2 minute check cycle. The automatic bilge pump can be started at any time by turning the power off; waiting 5 seconds and then turning the power back on. The pump will start immediately and pump until the water is removed. • Lightweight, compact pump with a tough plastic body and integral strainer • Features two leads, an automatic (brown) and a manual override (brown with a white stripe) • Quick release strainer allows for rapid cleaning of the submersible bilge pump internal components • Recommended for discharge heads up to a maximum of 2 metres • Meets ISO8846 marine (ignition) and ISO8849 marine (bilge pump) standards

JAB-20SA

Part no.

Model

Volts

Amp draw

Maximum flow rate lph (US gph)

Outlet mm (inch)

JAB-20SA JAB-25SA

20SA 25SA

12V 12V 24V 12V 12V 12V

2.8A 1.6A 0.9A 3.3A

3028 (800) 1892 (500) 1892 (500) 4164 (1100) 5678 (1500) 7571 (2000)

19 (3/4”) 19 (3/4”) 19 (3/4”)

JAB-25SA-24

25SA-24

JAB-27SA

27SA

25 (1”) or 28 (1-1/8”)

504106 504116

51S 53S

9A

28 (1-1/8”) 28 (1-1/8”)

15A

504116

For pump dimensions, please see online at www.asap-supplies.com

224

info@asap-supplies.com

www.asap-supplies.com

01502 716993