example

FITTINGS & THROUGH HULL OUTLETS

EXHAUST TEMPERATURE ALARMS

•

Designed for water injected exhaust systems

• Provides a visual and an audible alarm when the temperature inside the exhaust hose or the muffler exceeds an acceptable level • The temperature sensors are to be fitted into the exhaust hose or a Vetus waterlock / muffler and the alarm unit must be ordered separately • In the case of a twin engine installation 2 sensors may be connected to 1 alarm unit if so required • One sensor may also serve two alarm units, e.g. in the case of a second steering position

EXHAUST

403057

403643

CR (DZR) brass, bronze and stainless steel 316 through hull fittings make excellent exhaust outlets. The threaded body means you can fit it to a ball valve where applications call for the exhaust to be closed when the engine is not running. Please see Fittings, Valves and Strainers section, page 113.

Part no.

Volts Sender

Sender (Muffler mount)

(Hose mount)

V-XHI12B 12V V-XHI24B 24V

413158 413158

413159 413159

V-XHI12B

SUPERFLEX MARINE EXHAUST HOSE Suitable for the discharging of wet exhaust gas

• •

Suitable for wet exhaust systems only

• Not only tough, but also extremely flexible to help make the installation as easy as possible • Approved to R.I.N.A. and Lloyd’s register specification • Black corrugated cover is resistant to abrasion, oils and marine agents • Self-extinguishing CB / NBR rubber • The reinforcement is by double wire helix and textile plies • Inside is finished smooth NBR rubber • Temperature range: -25°C to +120°C • Working pressure: 43.5 PSI (3 bar) • Burst pressure: 130 PSI (9 bar) • Available in coils or per metre cut from a coil • Other sizes available, please contact us or visit our website at www.asap-supplies.com

Per metre

Per coil 10 metres

Per coil 20 metres

I.D. mm (inch)

O.D. mm

Inner bend radius mm

Stainless steel 316 superclamp to suit

412519 - 412525 - 412530 -

412519-20 19 (3/4”) 412525-20 25 (1”) 412530-20 30 (1-3/16”)

416803 416805 416806 416807 416808 416809 416810 416811 416813 416814 416815 416816 416816 416819 416820 416822 416822 416823 416826 416830

29 34 38 40 46 48 53 60 65 70 74 80 86

80

100 120 130 150 160 180 200 220 240 250 280 300 360 400 440 460 500 825

412532 412532-10 412532-20 32 (1-1/4”) 412538 412538-10 412538-20 38 (1-1/2”) 412540 412540-10 412540-20 40 (1-9/16”) 412545 412545-10 412545-20 45 (1-3/4”) 412551 412551-10 412551-20 51 (2”) 412555 412555-10 412555-20 55 (2-1/6”) 412560 412560-10 412560-20 60 (2-3/8”) 412563 412563-10 412563-20 63 (2-1/2”)

412591

412570 412570-10 -

70 (2-3/4”)

412576 412576-10 412576-20 76 (3”)

412589 412589-10 - 412591 412591-10 - 412592 412592-10 - 412594 412594-10 - 412593 412593-10 - 412595 412595-10 - 412597 412597-10 -

89 (3-1/2”)

102 114 122 126 139 165 219

Use this to work out how much water is in your exhaust hose when engine is running. We advise at the very maximum, you should have 50% water in the hose. Inner radius (cm) x inner radius (cm) x length (cm) x Pi (3.14159), divided by 2, divided by 1000 = capacity (litres) of water in exhaust hose when engine is running.

102 (4”)

110 (4-3/8”) 114 (4-1/2”)

127 (5”) 152 (6”) 203 (8”)

1200

ANTI-SIPHON DEVICES

BRASS ANTI-SIPHON LOOPS & SIPHON BREAK VALVES

For full details on Anti-Siphon Loops, Break Valves and complete kits, please see Fittings, Valves & Strainers section, page 136.

V-ASDH

V-ASDV

For Vetus anti-siphon devices, please see Fittings, Valves and Strainers section, pages 136-137.

410031

410023

109

info@asap-supplies.com

www.asap-supplies.com

01502 716993